Nanofluids, micro-lubrications and machining process optimisations − a review
Manufacturing Rev., 10 (2023) 1
Published online: 2023-01-10
Articles citing this article
The Citing articles tool gives a list of articles citing the current article.
The citing articles come from EDP Sciences database, as well as other publishers participating in CrossRef Cited-by Linking Program. You can set up your personal account to receive an email alert each time this article is cited by a new article (see the menu on the right-hand side of the abstract page).
Cited article:
This article has been cited by the following article(s):
Experimental investigation on mixed spray characteristic of cryogenic nano-minimum quantity lubrication in milling nickel base superalloy
MD Rahatuzzaman Rahat, Guolong Zhao, Umayar Ahmed, Zhiwen Nian, Ning He and Aqib Mashood KhanMachining Science and Technology 30 (2) 337 (2026)
https://doi.org/10.1080/10910344.2026.2625729
Investigation of turning performance in Al-7075-T6 using textured tools and CNT-MoS 2 hybrid nanofluid
Kejun Zhu, Mouchu Fu and Zhigang ChenMaterials and Manufacturing Processes 40 (9) 1256 (2025)
https://doi.org/10.1080/10426914.2025.2491401
Novel Application of Alumina Nanoparticle-enriched Cutting Fluid for the Surface Integrity and Machining of 17-4PH Steel
Vivek John, Saurabh Aggarwal, Ankit D. Oza, Manoj Kumar and Prince JainCurrent Nanomaterials 10 (4) 485 (2025)
https://doi.org/10.2174/0124054615333986241004114240
Steady and Periodical Heat-Mass Transfer Behavior of Mixed Convection Nanofluid with Reduced Gravity, Radiation and Activation Energy Effects
Cyrus Raza Mirza, Zia Ullah, A. Dahshan, Md. Mahbub Alam, Khadija M. Abualnaja, Hanaa Abu-Zinadah, Abdullah A. Faqihi and Nidhal Ben KhedherCase Studies in Thermal Engineering 105376 (2024)
https://doi.org/10.1016/j.csite.2024.105376
Small-Quantity Cooling Lubrication in Creep-Feed Grinding: Surface Quality and Residual Stress Analysis
Ali Basem, Malak Naji, Hasan A. Al-Asadi, Mohammad Sediq Safi, Gulrux Daminova, Merwa Alhadrawi, Mohamad J. Alfaker and Saiful IslamResults in Engineering 102348 (2024)
https://doi.org/10.1016/j.rineng.2024.102348
Applicability of nano-cutting fluids for enhanced cooling, low tool wear, and high tribological performance during machining—a review
Milon Selvam Dennison, S. Kirubanidhi Jebabalan and Debabrata BarikDiscover Applied Sciences 6 (12) (2024)
https://doi.org/10.1007/s42452-024-06398-9
Environmental sustainability during machining of hardened steel using nanofluid: A case study
Saswat Khatai, Ashok Kumar Sahoo, Ramanuj Kumar, Amlana Panda, D.A. Joshi, N.B. Ibrahim and D.M. SangeethaE3S Web of Conferences 405 04042 (2023)
https://doi.org/10.1051/e3sconf/202340504042
Development of OCMNO algorithm applied to optimize surface quality when ultra-precise machining of SKD 61 coated Ni-P materials
Le Anh Duc, Pham Minh Hieu and Nguyen Minh QuangManufacturing Review 10 7 (2023)
https://doi.org/10.1051/mfreview/2023006
Grinding with minimum quantity lubrication: a comparative assessment
Y. S. Dambatta, Changhe Li, Min Yang, L. I. Beikai, Teng Gao, Mingzheng Liu, Xin Cui, Xiaoming Wang, Yanbin Zhang, Zafar Said, Shubham Sharma and Zongming ZhouThe International Journal of Advanced Manufacturing Technology 128 (3-4) 955 (2023)
https://doi.org/10.1007/s00170-023-11962-5