Open Access
Manufacturing Rev.
Volume 7, 2020
Article Number 16
Number of page(s) 8
Published online 05 May 2020
  1. Z.Y. Liu, Q.Z. Wang, B.L. Xiao, Z.Y. Ma, Y. Liu, Experimental and modeling investigation on SiCp distribution in powder metallurgy processed SiCp/2024 Al composites, Mater. Sci. Eng. A 527 (2010) 5582–5591 [CrossRef] [Google Scholar]
  2. B.K. Prasad, S.V. Prasad, A.A. Das, Abrasion-induced micro structural changes and material removal mechanisms in squeeze-cast aluminum alloy-silicon carbide composites, J. Mater. Sci. 27 (1992) 4489–4494 [CrossRef] [Google Scholar]
  3. B.N.P. Bai, B.S. Ramasesh, M.K. Surappa, Dry sliding wear of A356-Al-SiCp composites, Wear 157 (1992) 295–304 [CrossRef] [Google Scholar]
  4. C.S. Lee, Y.H. Kim, K.S. Han, T. Lim, Wear behaviour of aluminum matrix composite materials, J. Mater. Sci. 27 (1992) 793–800 [CrossRef] [Google Scholar]
  5. A.P. Sannino, H.J. Rack, Dry sliding wear of discontinuously reinforced aluminum composites: review and discussion, Wear 189 (1995) 1–19 [CrossRef] [Google Scholar]
  6. A. Sreenivasan, S. PaulVizhian, N.D. Shivakumar, M. Muniraj, M. Raguraman, A study of microstructure and wear behaviour of TiB2/Al metal matrix composites, Latin Am. J. Solids Struct. 8 (2011) 1–8 [CrossRef] [Google Scholar]
  7. V. Gaitonde, S. Karnik, M. Jayaprakash, Some studies on wear and corrosion properties of AL5083/Al2O3/graphite hybrid composites, J. Miner. Mater. Character. Eng. 11 (2012) 695–703 [Google Scholar]
  8. K. Ravi Kumar, K.M. Mohanasundaram, G. Arumaikkannu, R. Subramanian, Analysis of parameters influencing wear and frictional behaviour of aluminium–fly ash composites, Tribology Trans. 55 (2012) 723–729 [CrossRef] [Google Scholar]
  9. L. Zhang, X.B. He, X.H. Qu, B.H. Duan, X. Lu, M.L. Qin, Dry sliding wear properties of high volume fraction SiCp/Cu composites produced by pressureless infiltration, Wear 265 (2008) 1848–1856 [CrossRef] [Google Scholar]
  10. R. Shanawaz Patil, P. Madhu, B.P.G. Manjunath, M. Kalyana Kumar, Investigation of mechanical properties and wear behavior of Lm 25 Aluminum Alloy reinforced with silicon carbide and activated carbon, Int. J. Res. Sci. Innov. 5 (2018) 70–77 [Google Scholar]
  11. C. Ravi, G.B. Rudrakshi, S.M. Jigajinni, A study on dry sliding wear behaviour of Al-6061 redmud composite, Int. J. Innov. Res. Sci. Eng. Technol. 5 (2016) 7827–7832 [Google Scholar]
  12. P. Amuthakkannan, V. Manikandan, M. Ayyanar Raja, S. Rajesh, Wear characterization of aluminium/basalt fiber reinforced metal matrix composites − a novel material, Tribol. Ind. 39 (2017) 219–227 [CrossRef] [Google Scholar]
  13. M. Arulraj, P.K. Palani, L. Venkatesh, Experimental investigation on dry sliding wear behaviour of hybrid metal matrix (Al-Al2O3-B4C) composite, Int. J. ChemTech Res. 9 (2016) 359–364 [Google Scholar]
  14. H.B. Bhaskar, A. Sharief, Tribological properties of aluminium 2024 alloy-beryl particulate MMC's' bonfring, Int. J. Ind. Eng. Manag. Sci. 2 (2012) 143–147 [Google Scholar]
  15. J. Ahemad, R.A. Kapgate, N.D. Sadaphal, Y.H. Ahire, Tribological behavior of AL-LM25 and SiC, Int. Res. J. Eng. Technol. 2 (2015) 893–897 [Google Scholar]
  16. W. Narayan, Mannurkar, P.U. Raikar, Investigation of dry sliding wear behaviour of LM4 (Al − Si and Cu) − T6/LM6 (Al-Si12)-M using Taguchi approach, Int. Res. J. Eng. Technol. 2 (2015) 66–74 [Google Scholar]
  17. S. Mahdavi, F. Akhlaghi, Effect of SiC content on the processing, compaction behavior and properties of Al6061/SiC/Gr hybrid composites, J. Mater. Sci. 46 (2011) 1502–1511 [CrossRef] [Google Scholar]
  18. F. Akhlaghi, S. Mahdavi, Effect of the SiC content on the tribological properties of hybrid Al/Gr/SiC composites processed by in situ powder metallurgy (IPM) method, Adv. Mater. Res. 264–265 (2011) 1878–1886 [CrossRef] [Google Scholar]
  19. S. Das, S. Das, K. Das, Abrasive wear of zircon sand and alumina reinforced Al-4.5 wt. percent Cu alloy matrix composites − A comparative study, Compos. Sci. Technol. 67 (2007) 746–751 [CrossRef] [Google Scholar]
  20. G. Ranganath, S.C. Sharma, M. Krishna, Dry sliding wear of garnet reinforced zinc/aluminium metal matrix composites, Wear 251 (2001) 1408–1413 [CrossRef] [Google Scholar]
  21. K. Umanath, K. Palanikumar, S.T. Selvamani, Analysis of dry sliding wear behaviour of Al6061/SiC/Al2O3 hybrid metal matrix composites, Composites: Part B 53 (2013) 159–168. [CrossRef] [Google Scholar]
  22. C.P. Fung, Manufacturing process optimization for wear property of fibre-reinforced polybutylene terephthalate composites with grey relational analysis, Wear 254 (2003) 298–306 [CrossRef] [Google Scholar]
  23. N. Tosun, C. Cogun, H. Pihtili, The effect of cutting parameters on wire crater sizes in wire EDM, Int. J. Adv. Manuf. Technol. 21 (2003) 857–865 [CrossRef] [Google Scholar]

Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.

Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.

Initial download of the metrics may take a while.