Open Access
Manufacturing Rev.
Volume 9, 2022
Article Number 11
Number of page(s) 12
Published online 06 June 2022
  1. P.H. Nayak, H.K. Srinivas, M. Nagaral, Characterization of tensile fractography of nano ZrO2 reinforced copper-zinc alloy composites, Frattura ed Integrity Strutturale (Fracture and Structural Integrity) 48 (2019) 370–376 [Google Scholar]
  2. N. Fazil, V. Venkataramana, M. Nagaral, V. Auradi, Synthesis and mechanical characterization of micro B4C particulates reinforced AA2124 alloy composites, Int. J. Eng. Technol. UAE 7 (2018) 225–229 [Google Scholar]
  3. N.G. Siddesh Kumar, G.S. Shivashankar, S. Basavarajappa, R. Suresh, Some studies on mechanical and machining characteristics of Al2219/n-B4C/MoS2 nano hybrid metal matrix composites, Measurement 107 (2017) 1–11. [CrossRef] [Google Scholar]
  4. G. Pathalinga Prasad, H.C. Chittappa, M. Nagaral, V. Auradi, Effect of the reinforcement particle size on the compressive strength and impact toughness of LM29 alloy-B4C composites, Struct. Integr. Life 19 (2019) 231–236 [Google Scholar]
  5. P.R. Jadhav, B.R. Sridhar, M. Nagaral, J. Harti, Mechanical behavior and fractography of graphite and boron carbide particulates reinforced A356 alloy hybrid metal matrix composites, Adv. Compos. Hybrid Mater. 3 (2020) 114–119 [CrossRef] [Google Scholar]
  6. C.S. Ramesh, R. Noor Ahmed, M.A. Mujeebu, M.Z. Abdullah, Development and performance analysis of novel cast copper SiC-Gr hybrid composite, Mater. Des. 30 (2009) 1957–1965 [CrossRef] [Google Scholar]
  7. V. Hiremath, S.T. Dundur, R.L. Bharath, G.L. Rajesh, V. Auradi, Studies on mechanical and machinability properties of B4C reinforced 6061 aluminium MMC produced via melt stirring, Appl. Mech. Mater. 592 (2014) 744–748 [CrossRef] [Google Scholar]
  8. N. Verma, S.C. Vettivel, Characterization and experimental analysis of boron carbide and rice husk ash reinforced AA7075 aluminium alloy hybrid composites, J. Alloys Compd. 741 (2018) 981–998 [CrossRef] [Google Scholar]
  9. M. Nagaral, V. Auradi, K.I. Parashivamurthy, S.A. Kori, B. K. Shivananda, Synthesis and characterization of Al6061-SiC-graphite composites fabricated by liquid metallurgy, Mater. Toady Proc. 5 (2018) 2836–2843 [Google Scholar]
  10. J. Singh, A. Chuan, Fabrication characteristics and tensile strength of novel Al2024-SiC-red mud composites processing via stir casting route, Trans. Nonferrous Metals Soc. China 27 (2017) 2573–2586 [CrossRef] [Google Scholar]
  11. H. Beygi, S.A. Sajjadi, S.M. Zebarjad, Preparation and characterization of squeeze cast-Al–Si piston alloy reinforced by Ni and nano-Al2O3 particles, J. King Saud Univ. Eng. Sci. 28 (2016) 230–239 [Google Scholar]
  12. N. Nagaraj, K.V. Mahendra and M. Nagaral, Microstructure and evaluation of mechanical properties of Al-7Si-fly ash composites, Mater. Today: Proc. 5 (2018) 3109–3116 [CrossRef] [Google Scholar]
  13. C. Saravanan, K. Subramanian, V.A. Krishnan, R.S. Narayanan, Effect of particulate reinforced aluminium metal matrix composite – a review, Mech. Mech. Eng. 19 (2015) 23–23 [Google Scholar]
  14. G.B. Veereshkumar, C.S.P. Rao, N. Selvaraj, Mechanical and tribological behavior of particulate reinforced aluminium metal matrix composites – a review, J. Minerals Mater. Character. Eng. 10 (2011) 59–91 [Google Scholar]
  15. M. Nagaral, R.G. Deshapande, V. Auradi, S. Babu Boppana, S. Dayanand, M.R. Anilkumar, Mechanical and wear characterization of ceramic boron carbide-reinforced Al2024 alloy metal composites, J. Bio-and Tribo-Corros. 7 (2021) 1–12 [CrossRef] [Google Scholar]
  16. M. Nagaral, V. Auradi, K.I. Parashivamurthy, S.A. Kori, Wear behavior of Al2O3 and graphite particulates reinforced Al6061 alloy hybrid composites, Am. J. Mater. Sci. 5 (2015) 25–29 [Google Scholar]
  17. M. Nagaral, V. Auradi, S.A. Kori, H.N. Reddappa, Jayachandran, V. Shivaprasad, Studies on 3 and 9 wt.% of B4C particulates reinforced Al7025 alloy composites, AIP Conf. Proc. 1859 (2019) 020019 [Google Scholar]
  18. J. Harti, T.B. Prasad, M. Nagaral, K. Niranjan Rao, Hardness and tensile behavior of Al2219-TiC metal matrix composites, J. Mech. Eng. Autom. 6 (2016) 8–12 [Google Scholar]
  19. V. Bharath, V. Auradi, M. Nagaral, S. Babu Boppana, Experimental investigations on mechanical and wear behaviour of 2014Al–Al2O3 composites, J. Bio-and Tribo-Corros. 6 (2020) 1–10 [CrossRef] [Google Scholar]
  20. S.N. Prashant, M. Nagaral, V. Auradi, Preparation and evaluation of mechanical and wear properties of Al6061 reinforced with graphite and SiC particulate metal matrix composites, Int. J. Mech. Eng. Robot. Res. 1 (2012) [Google Scholar]

Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.

Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.

Initial download of the metrics may take a while.